-
Version 2.6.0.7
- Minor change related to the production of new devices.
Version 2.6.0.6
- Added safety precaution if firmware update process failed during installation when updating from a non-recent firmware version.
Version 2.6.0.3
- Added device provisioning service and new IoT hub options
- Fixed an authentication issue related to cloud commands
- Improved the OTA process by adjusting the HMI to show “in progress” for all processes related to the installation and configuration of a new firmware.
- LTE power sequence improvements and fixed an issue where in some cases the module wouldn’t properly power down in non-LTE mode.
- Improvements for OCPP Native (See OCPP release notes)
- Various smaller improvements and fixes.
Version 2.5.1.0
- Improved cybersecurity features and behavior of the charging station to fully comply with the new cybersecurity requirements in EU.
- Added OCPP Security whitepaper
- Various improvements for OCPP Native (See OCPP release notes)
- Pin code is now updatable by the owner
- Merged Zaptec Go UK and Zaptec Go EU firmware
- Added OCPP 1.6J to Zaptec Go UK
Version 2.5.0.3
- Updated IoT Development Framework in preparations for future updates.
Version 2.4.2.4
- Improved LTE stability and reconnection handling
- Adjusted signal strength calculation
- Improved event handling logic
- Added PowerDelta support for OCPP Native
- Improved activation status handling for OCPP Native in offline mode
Version 2.4.1.8
- Improved NTP (time server) connectivity
- Enhanced OCPP Native smart charging
- Improved state transitioning in OCPP Native
Version 2.4.1.2
- Added support for OCPP 1.6J
- Improved performance under high temperatures
Version 2.3.1.2
- Added support for MIFARE DESFire RFID tags
- Improved behaviour when responding to a large number of charging restart events
- Enhanced session reporting
Version 2.1.1.2
- Improved time server connectivity
Version 2.1.0.8
- Improved charging initialization sequence
Version 2.1.0.4
- Added support for MID-calibrated chargers
- Improved support for Mifare Classic RFID-tags
- Added support for toggling IT3-phase optimization with App v5.10.1 or later
- Reporting and configuration improvements
Version 2.0.4.6
- Improved session handling
- Improved event handling
Version 2.0.4.0
- Adds RCD Test button function for use with the App
- Corrects chargers where no sessions are reported
Version 2.0.2.2
- Improved 4G connectivity
- Improved OTA reliability on poor links
- Improved certificate handling
- Added support for future use on Go UK
Version 1.1.0.9
- Added active use of the portal "Maximum current" parameter when 1-phase charging is used on IT 3-phase grid
Version 1.1.0.6
- Minor improvements
Version 1.1.0.5
- Minor improvements
- Improved connectivity
Version 1.1.0.4
- Minor improvements
Version 1.1.0.3
- Offline session handling: Complete Charge History and Session Information are now fully available with the Zaptec Go
- Full support for OCPP in the cloud
- Other changes:
- Minor data usage optimization
- Improvements in connectivity between the charger and cloud
- The LED on the Zaptec Go will now reflect when the charger is operating offline
Version 0.0.4.0
- Improved Cloud connectivity
Version 0.0.3.8
- Improved IT3 phase optimization
- Improved eMeter usage
- Improved cloud state exchange
- Improved response to cloud commands
Version 0.0.2.9
- Added support for RFID pairing with version 5.0.0 of the App
- Added RFID and App authentication feature
Version 0.0.2.7
- General adjustments on energy reporting
Version 0.0.2.3
- Fixed energy accumulation issue seen on charger meter value in some cases
- Wifi signal strength is now communicated to the App during setup
- Improved power grid type detection
- Improved waiting state in system mode if car has delayed charging
- Improved support for cloud control when the charger is installed using the switch for configuration
Version 0.0.1.22
- Improved 4G connectivity on mobile networks outside of Norway
- Improved sensitivity on relay safety check
Version 0.0.1.11 (Changes since version 0.0.0.71)
- Improved request charging messaging in system mode
- Improved syncing and application of offline current settings
- Charger now allows up to 40A fuse setting
- Active phases now also reported in standalone
- Bluetooth support for "Upgrade firmware" and "Restart charger"
- Raised threshold for reducing current under high temperature
- Optimized IT 3-phase behavior for multi-charger setups
- Fixed communication setting that could leave charger unresponsive
- LED now turns white 2 minutes after charging ends in system mode
-
Version 3.2.1.0
- OCPP 1.6J support added (See separate OCPP 1.6J release notes)
- Added new symbol for waiting for EV to disconnect
- HMI improvements
- Fixed an issue where sometimes RFID wouldn't be ignored when the charging station is disabled
- Fix for a bug that causes the charger icon to be stuck in loading when paused by cloud due to schedule in Zaptec mode
- Other minor fixes and improvements
Version 3.1.0.3
- Minor change related to the production of new devices.
Version 3.1.0.2
- Added device provisioning service and new IoT hub options
- Improved the OTA process by allowing for rollback if the process failed during the installation.
- Improved the OTA process by adjusting the HMI to show “in progress” for all processes related to the installation and configuration of a new firmware.
- Fixed an issue with the installation flow where the detected grid type wasn’t stored properly.
- Fixed an issue where Stop/Pause charging with a RFID tag wouldn’t stop the session properly.
- Various smaller improvements and fixes.
Version 3.0.3.2
- Improved cybersecurity features and behavior of the charging station to fully comply with the new cybersecurity in EU
- Pin code is now updatable by the owner
- Added locking symbol (cable lock) whenever the cable is in locked state.
- Improved the HMI Display by adding more states and optimizing flow between states.
- Fixed an issue where sometimes the wrong offline current would be set.
- Fixed an issue where the display could in some cases be stuck during an OTA update.
- Various smaller improvements and fixes.
Version 3.0.2.1
- Improved cellular connectivity
- Fixed an issue related to system performance
- Fixed an issue which could sometimes cause the charger to unexpectedly restart
- Improved security
- Fixed an issue where warnings wouldn’t trigger red light
- Other minor fixes and improvements
Updated